Do you have a favourite cup that's got a chip in it? This front panel is then ready to nail to your box. Before you add the front panel, make a hole that will become the bird’s entrance into their new home. Now hang your tea cup bird feeder in your garden for the birds to enjoy and you to admire. The return of birdsong and the dawn chorus is a sure sign that warm weather is on the way. For blue tits, the hole should be 28mm across (same as a ten pence piece) and up to 4mm bigger than that for larger box nesting birds. There again, I would say with regards to all the little extras don’t sweat it. It isn’t 100% necessary, but a plate is very good for keeping predatory birds and squirrels away from the baby birds. We have had to put up a sign to make sure nobody stuffs out their cigarettes on the babies heads. You’re going to need a plank of wood that’s about 15mm thick to give the birds inside the insulation they’ll need. I will check that and replace with a smooth roof if necessary. When putting the bird house together, the options are to either glue and pin or use screws. Fill the bottle with bird seed and place the lid back on. Well I think from the photo you will agree that the hole is about two centimetres too high on the front panel. The sides has some screw holes, but since a bit of ventilation is a good thing I didn’t fill them in. Sealing can be achieved with a water-based exterior paint or varnish, but is not strictly necessary. I did this by cutting in a box section on each sides and then simply sliding in the base during construction. Follow this step-by step guide from the team at Wicken Fen Nature Reserve and make your own homemade bird feeder, all you'll need is a plastic bottle, toilet roll or chipped cup. When breaking up wooden pallets you will always get a few short boards and a few split boards. Cut two holes in your plastic bottle, make sure they are directly opposite each other. I cut the pitch of the roof at 30 degrees which seems as good an angle as any. We use cookies to provide you with a better service. Now for the final step, drill a hole at the top of the bird box to attach it to the perfect spot you’ve identified in your garden. We use cookies to provide you with a better service. Place your seed covered fat into the cup and press down to ensure it stays in. Roll your toilet roll in the seed mixture until it's coated. Follow this step-by step guide from the team at Wicken Fen Nature Reserve and make your own homemade bird feeder, all you'll need is a plastic bottle, toilet roll or chipped cup. I just love working with smooth clean wood. Find a new use for an old cup with this bird feeder idea, Make something to feed your feathered friends, Find a new use for your old plastic bottles. You can do this with a wide drill bit and depending on the sort of birds you want to attract - we’d recommend a hole measuring 25mm for blue tits and up to 32mm for house sparrows. Tie your string around the top of the bottle. For the roof I joined a couple of palette ends together to make a slightly wider piece. That is particularly important after rain to dry out the wood quickly. Thread the string through and tie a knot. My piece of pallet was 12 centimetres wide so the sizes I used for each of the pieces are as follows: As you can see I sanded the pallet wood down to smooth and clean surfaces (a very rewarding task in itself) but this was for my benefit rather than strictly for the birds. Repeat this with another two holes, slightly higher up. Make sure to smooth off rough edges on the plate to avoid hurting the bird boxes inhabitants. For the bird seed, we recommend buying a small seed mixture. After all birds are not fussy or at least they’re not following the same rules of what is good accommodation that we are. The best position for a box is to be north-east facing, around 2-4 metres above the ground away from predators, with a clear flight path to the entrance hole. And the best bit; bird boxes are really easy to build using only the most basic tools. Start by cutting the four main pieces from off-cuts of pallet that are all of equal width. Cover with seeds. Alongside about a metre of pallet wood (a nice wide board) you will need: There are extras to consider and one of the key ones is a plate made of metal around the entrance hole. I added some ridges for decorative effect, but that was probably a silly idea as it may stop the water from running off as quickly. I then sanded the edges and a slight recess where I glued in a brass hole plate to keep predators at bay. For the roof we recommend you use self-tapping screws or a hinge, so that you can remove it later to make it easier to clean the bird box out in the autumn. Wicken Fen is home to some of our rarest and most endangered species. The cigarette disposal ashtray outside my office door is currently home to a nest of blue tits. A great way to help birds at this time of year is to put up nest boxes, where birds can raise a clutch of young come the spring. Before you hang it in your garden, poke some twigs through to act as a perch.

.

Healthy Kimchi Soup, Tea Cup With Infuser And Lid, Air Nz Share Price Forecast, Armour Vienna Sausage Nutrition Info, Hmong Beef Larb Recipe, Periodo Ipotetico Italiano Esercizi, Han Kang Husband, Kodiak Cakes Waffles Calories,